Bahasa MelayuBahasa Melayu
//RuangSimThe simulation lab
Home / Guides / Road hierarchy: fixing traffic without demolishing your city
GUIDE

Road hierarchy: fixing traffic without demolishing your city

Three road tiers, one connection rule. A technical traffic guide you can apply gradually to an already jammed city.

Road hierarchy: fixing traffic without demolishing your city

Traffic jams in Cities: Skylines are rarely about road quantity; they are about road relationships. A city with fewer roads but correct hierarchy flows better than a road-packed city where everything connects to everything.

Tier one: highways. They serve districts, not houses. A residential zone with direct highway access generates hundreds of trips that cut through the whole city.

Tier two: arterials. They connect districts to highways. The rule: arterials must not hit signalised intersections too close together - at least twenty grid squares apart.

Tier three: local roads. They serve houses and shops only, and meet arterials at a limited number of points. This is the rule players break most: every small street feeds the main road, and every car takes the same 'shortest' route.

Rollout step one: start with industry. Industrial zones generate the heaviest goods traffic. Give freight its own corridor that never crosses downtown, then move cargo terminals to the map edge.

Finally, transit before asphalt. One metro line linking residential zones with the job core removes more private cars than two new lanes. Add roads only once transit is full - and your city starts moving within a week.

Congestion is usually a hierarchy problem

When a city grid jams, the instinct is to widen the road. That rarely works, because most jams are caused by too many different trip lengths sharing one piece of asphalt, not by a shortage of lanes. A local street, a collector, an arterial and a highway each have a job. Mixing them produces the classic symptom: a six-lane avenue that still gridlocks because every driveway feeds directly into it.

The four levels and what each is for

  • Local street. Access to buildings. Low speed, frequent junctions, no through traffic.
  • Collector. Gathers several local streets and carries them to an arterial. Some junctions, still signal-controlled.
  • Arterial. Moves traffic across the district. Limited access points, longer blocks, higher speed.
  • Highway / express. Between districts only. No direct property access at all.

The mistake is almost always a missing collector. Without it, local streets dump straight onto an arterial, every junction becomes a conflict point, and the arterial's capacity is consumed by cars turning rather than cars travelling.

Five fixes that do not require demolition

  1. Remove access points. In Cities: Skylines, upgrading a road with fewer driveways or converting intersections to restricted crossings often beats adding lanes.
  2. Separate the turns. Dedicated turning lanes and a slightly longer signal phase remove the vehicle that blocks a whole green light while waiting for a gap.
  3. Give through traffic a bypass. Even a two-lane parallel route around a commercial strip pulls a surprising share of trips away from the main road.
  4. Move the destination, not the road. Relocating one high-traffic service building (a cargo terminal, a stadium, a large commercial block) can dissolve a jam that three road upgrades did not touch.
  5. Add a mode, not a lane. A bus or metro line changes how many vehicles exist. Widening a road only changes how many can queue.

Reading the jam before changing anything

Spend two minutes classifying the queue. Is it spillback (a downstream junction cannot clear), weaving (too many lane changes in a short distance), or demand (more trips than any road could carry)? The first is fixed at the downstream junction, the second by separating access points, and only the third by adding capacity. Widening the road where the queue is visible fixes a spillback in the wrong place, every time.

In Cities: Skylines II the traffic view makes this easier: click the jammed segment and follow where the vehicles are actually going. If 70% of them are passing through without a local destination, you do not have a local road problem, you have a missing arterial.

Why this transfers to other simulation games

The same idea shows up as logistics belts in Factorio and train signals in any railway builder. A network that merges slow local flows directly into a fast trunk behaves badly regardless of whether the units are cars, plates or wagons. Once you start asking "which level is this link supposed to be?", most congestion problems stop looking like capacity problems and start looking like classification problems.

Read next

Frequently asked questions

Why does widening a road often fail to fix traffic?

Because the jam is usually caused by different trip lengths sharing one link, not by a lane shortage. Local access traffic consumes the arterial's capacity through turning conflicts. Adding a collector level fixes more than adding lanes.

What is the most commonly missing road level?

The collector. Without it, local streets feed straight into an arterial, creating a conflict point at every junction and turning a high-capacity road into a slow car park.

How do I tell a spillback from a genuine capacity problem?

Follow where the queued vehicles are going. If the blockage clears downstream when a junction is retimed, it is spillback. Only when more trips exist than any configuration could carry do you need extra capacity.

Can moving one building really dissolve a jam?

Yes. Cargo terminals, stadiums and dense commercial blocks generate trip volumes out of proportion to their footprint. Relocating one near a different network level often outperforms several road upgrades.

Is public transport just a capacity fix in disguise?

It changes the number of vehicles rather than the number that can queue, which is why it addresses demand where widening addresses only storage. They solve different parts of the same problem.

Does road hierarchy apply to factory and railway games?

The principle does. Merging slow local flows directly into a fast trunk causes the same failures with conveyor belts and train signals as it does with cars.