Bahasa MelayuBahasa Melayu
//RuangSimThe simulation lab
Home / Guides / First-factory economics: the numbers to know before you place a belt
GUIDE

First-factory economics: the numbers to know before you place a belt

Production ratios are not a hobby; they are the difference between a growing factory and a starving one. Four core numbers decide everything.

First-factory economics: the numbers to know before you place a belt

Every jammed factory shares one history: the player placed machines because they looked tidy, not because of numbers. The four numbers below change how your first factory gets built.

Number one: miner rate. One iron miner produces 30 items per minute at basic level. Every downstream decision starts from this number - if your build needs 60, you need two miners, not 'add later'.

Number two: furnace ratio. One furnace consumes 15 ore per minute and yields 15 plates. Two miners means four furnaces, not three. A single mismatched ratio creates queues that slow everything.

Number three: belt capacity. A yellow belt moves 15 items per second - twice one miner's need and less than two. Counting belt capacity before building parallel lines is the habit that separates growing factories from tangled ones.

Number four: power headroom. Build 1.3 times your electricity need, not 1.0. Pollution-driven mining slowdowns and sudden outages always arrive at the worst moment, and a thirty percent margin turns that event into a small problem.

With these four numbers your first factory will not be perfect - but it will grow. And a growing factory is the only kind that is fun to fix.

Ratios, not vibes

A first factory almost always fails for the same reason: somebody built one more assembler because the belt looked short, and the whole line starved three steps upstream. The fix is to write the arithmetic down before placing anything. You need three numbers per item: how many per minute the consumer needs, how many per minute one producer makes, and how many items per minute the belt between them can carry.

Worked example: a Factorio starter line

Say you want one red science pack per second. A red pack assembler takes 5 seconds per craft, so one machine produces 0.2 packs/second and you need five assemblers. Each pack consumes one copper plate and one gear. Gears take 0.5 seconds each, so one gear assembler supplies two pack assemblers; you need three (rounding up). Copper plates come from a furnace smelting one ore every 3.2 seconds, so five pack assemblers need roughly 1.6 furnaces' worth of copper, plus a second line for the iron feeding the gears.

Nothing here is exotic. It is division, and it tells you that five pack assemblers with one gear machine will idle. That idle is what players misread as "the game is slow".

Where Satisfactory changes the question

Satisfactory gives explicit rates in every machine's UI, which moves the bottleneck from recipes to belts. A Mk.1 conveyor moves 60 items/minute; a Miner Mk.1 on a normal node produces 60 ore/minute; a Smelter consumes 30 ore/minute for 30 ingots. So one miner feeds exactly two smelters, and any attempt to add a third is a rounding error you will spend twenty minutes diagnosing.

The practical rule: build to the slowest rated component, then leave a buffer. An industrial storage container between two stages will not fix a bad ratio, but it will let you see which side is emptying. That visibility is worth more than an extra machine.

The three failure signatures

  • Belts backing up at the input, empty at the output. Over-supplied upstream, starved downstream. Add consumers, not producers.
  • Machines blinking idle in a regular pattern. A ratio mismatch with a fast cycle. Recompute the middle stage.
  • Everything slows only after ten minutes. Usually a belt tier bottleneck or a power grid brownout, not a recipe problem. Check the throughput rating and the power graph before touching the layout.

Cities: Skylines is the same maths wearing a different coat

A city budget is a production line where the output is service coverage rather than ingots. One elementary school serves a fixed number of households; add residential zones beyond that and you get an education gap that shows up two in-game years later as labour problems. The delayed feedback is what makes city builders feel less precise than factory games, but the underlying question is identical: what is the consumption rate, and what is the capacity of the stage feeding it?

A five-line checklist before you place a belt

  1. Write the target output per minute.
  2. Divide by each machine's cycle time to get machine counts, rounding up.
  3. Compare every link against the belt tier you actually own.
  4. Add one buffer between stages so a mismatch is visible.
  5. Only then think about how tidy the layout looks.

We keep this on every factory review on RuangSim because it is the difference between a first base that scales and one you demolish at hour six.

Read next

Frequently asked questions

What is the single most common first-factory mistake?

Adding assemblers to fix a slow output when the real problem is an upstream shortage. Extra consumers starve the line further. Compute the required items per minute at each stage before placing anything.

Why does Satisfactory make ratios easier than Factorio?

Every machine shows an explicit per-minute rate, so the bottleneck shifts from recipe timing to conveyor tiers. One Miner Mk.1 at 60 items/minute feeds exactly two Smelters at 30 each.

Will a storage buffer fix a bad production ratio?

No. A buffer cannot create items. It makes the mismatch visible by showing which side empties, which is why it is worth placing even though it does not change throughput.

How do I recognise a belt-tier bottleneck?

The line runs fine at first and degrades after several minutes, with machines idling in a repeating pattern. Check the conveyor rating and the power graph before changing the layout.

Does this apply to city builders too?

Yes. A school or clinic has a fixed household capacity, and overzoning residential creates a service gap that only appears years later as labour or land-value problems. It is the same rate-versus-capacity question with delayed feedback.

Should I optimise the layout early?

No. Get the counts, belt ratings and one buffer right first. A tidy layout built on a wrong ratio is the base you end up demolishing at hour six.